Ryan Falconer Cross ram intakes available

[unchained01]

So am I to take it that these will fit a 2000+ aluminum head 3x00 ?

Here is the picture of the remaining intake collection on Falconer's shop floor. The lower manifold for aluminum heads is towards the top. Unfortunately and unknowingly to me, was taken by someone before it was sent to me, so I only have upper halves. The ports are quite large compared to OEM intakes.


[ATTACH=CONFIG]7248[/ATTACH]

not working link.

My buddy with that intake in his fiero, also had a couple of the aluminum blocks at one time too. he sold them off years ago though otherwise I would let him know you were looking for one.

here is an ITB intake on aluminum heads(gen 2 heads), from what I have heard it is a falconer piece.

http://www.youtube.com/watch?v=jLikjChQlPE

My buddy owns that intake. I think I posted that vid up here previously. From what my buddy says, 6 of those for the aluminum heads were made based on what he was told from the circle track guy he bought it from. I have seen pics of at least 2 of these aluminum head ones in existance. I think its pretty cool, and from what I am told, that hilborn style has enough meat in the runners to port open to gen 3 head specs. And stalkerv6 is correct. From what I have been told it was made by a small group of people in indiana.

My buddy modified his for efi but yes it was originally setup for mechanical fuel injection.

I have a fageol supercharger that I was going to bolt on, but if I can get this setup, pending on pics of what it comes with, I might go with this itb setup just for the show factor when opening up the hood.

[02dohc]

i will take one. how much for it and shipping to 55945. thank you and if you can email me at mtkrusmark@yahoo.com it would work easier for me. im looking at one of the iron head versions you have, also you did not specify if it was the whole intake setup or just parts. thank very interested

[Superdave]

I will be putting my ITB intake up for sale soon too. Being the only one made for a gen 3 I bet it goes quick. Sticker shock will scare quite a few people I'm sure though too. Lol.

Sent using Tapatalk 2

[stalkerV6]

Here is the picture of the remaining intake collection on Falconer's shop floor. The lower manifold for aluminum heads is towards the top. Unfortunately and unknowingly to me, was taken by someone before it was sent to me, so I only have upper halves. The ports are quite large compared to OEM intakes.

[stalkerV6]

You are close, but that's not a Falconer intake. If you look at it, it's a sprint car style intake. Two intakes like that were made in the 80s. The first was for cast iron intakes by Hilborn. The second was made by a father and son up in Fort Wayne in the 80s for sprint racing. I've met them on a handful of occasions and they still do fabrication work for me every couple of years. They still have the mold of this intake but it was changed some, so if you have the money to cast a one off, the modified version will need wider custom valve covers so you do not need to remove the entire manifold to make adjustments.

At one point in time, I was on a mission to collect every performance intake for the early 60 V6 for display or use. I'll see about getting photos of those intakes and post them at a later date.

[ericjon262]

look closer. it does not.

very similar, but you're right, it doesn't.

[ericjon262]

here is an ITB intake on aluminum heads(gen 2 heads), from what I have heard it is a falconer piece.

http://www.youtube.com/watch?v=jLikjChQlPE

[stalkerV6]

It appears Superdave has a picture of two intakes I have. They are the two side by side on the plaid table cloth from several years back. A Fiero owner was referred to me through Falconer. I think the guy had what you'd call sticker shock after speaking with Kinsler efi to re-engineer the intake and update it for today's efi technology. I came across a forum where the guy posted this picture and wrote as though he had actually made the purchase.

[stalkerV6]

I had a PM about the lower manifold not arriving at my house. The lower manifold that did not arrive was for the aluminum heads.

[unchained01]

Yeah it's also too bad these wont work on a aluminum head engine. But very interesting all the same I did some research on these the other projects. Nice !!!

[robertisaar]

those are certainly interesting....

i was hoping this wouldn't turn out like the Truleo intakes or whatever they're called that the Fiero guys seem to go nuts over.

[Superdave]

Here are the ones i have... I think i have more but i'll have to keep looking...







I'd love to have a set of those air filters for mine.. lol

Looks like it just bolts to a stock IH LIM.

look closer. it does not.