3500 plenum and wet nitrous

Collapse
X
 
  • Time
  • Show
Clear All
new posts

  • candychevy87
    replied
    i've seen them do it with mustangs, you can use the vaccum block and run the juice into a vaccum port on youre intake

    Leave a comment:


  • silvergtjrad
    replied
    Update- Im running a dry shot right now and having absolutely no problems. Tuning was a breeze. I pulled out 4* timing using the table for IAT vs. timing for my first couple of runs. It didnt knock at all, and it wasnt running lean. Ive been able to put 2* timing back in with no troubles at all.

    I just wish I could figure out my misfire problem now so I can spray at the track damnit

    Leave a comment:


  • IsaacHayes
    replied
    You can make it work, but if it was fitted for a 3100 then yeah it will change it slightly. I'm still runing the stock air box and air tube on the 3500 plenum and it fits, but the air tube to the box is a bit more squished.

    Leave a comment:


  • Z26-T
    replied
    oops, posted the same thing twice.

    Leave a comment:


  • Z26-T
    replied
    Owch, that's not really what I wanted to hear... I just realized that Everything that I mocked up was in a beretta with a 3.1 and the 3.5 is quite a bit different inlet wise. But thanks for reminding me.

    Leave a comment:


  • IsaacHayes
    replied
    I know at least one person running boost with the 3500, and soon to be another. Midnight had one for a while but went back to 3400 upper cause the neck was too low on the 3500 and was hitting his chargepipes/etc on something (downpipe maybe)

    Leave a comment:


  • Z26-T
    replied
    Originally posted by IsaacHayes View Post
    If you notice one of those pics isn't using the stock box. Those were pics when it wasn't finished. Likely had the stock box on there just to drive it until something else was put there. I'm using the stock box on mine with a K&N drop in, but my box is opened up to draw in more air than what the factory snorkel allows.

    Anyway, this is getting off topic. :P
    Yeah, that's prolly my fault for dissin on the stickers. Guess I cant say too much because there are stickers on the dragster...but thats cuz i get money for it :P.

    Sorry, anyways. So a 3.5 plenum is better than a 3.4 for forced induction appliclations too for better equalization of the boost. Right? So less chances of blowing up the two starved cylinder if they're all tuned properly.

    Leave a comment:


  • montess408
    replied
    i would use a set up like this with a ported 3500 manifold for the best performance
    http://www.holley.com/08006NOS.asp

    Leave a comment:


  • IsaacHayes
    replied
    If you notice one of those pics isn't using the stock box. Those were pics when it wasn't finished. Likely had the stock box on there just to drive it until something else was put there. I'm using the stock box on mine with a K&N drop in, but my box is opened up to draw in more air than what the factory snorkel allows.

    Anyway, this is getting off topic. :P

    Leave a comment:


  • powerdoctor
    replied
    I'm just messin about the stickers...lol.

    I thought it was your's and was just razzin ya about the stickers...

    The engine looked good though .... except for the stock air box....wtf?

    why do all of that and put that pos back in there?

    Leave a comment:


  • IsaacHayes
    replied
    Hey I like my ridiculous tube!

    And the guy's car with the stickers there is a 3.1mpfi hybrid with a 3400 top end, 3500 plenum, cam, headers, and runs 13's N/A. I don't think he ever ran it with that direct port nitrous. He ended up selling that setup. He's working on the car right now for some more power this time.

    Leave a comment:


  • powerdoctor
    replied
    The direct port is the best way to achieve equal distribution.

    If he is dead set on using a single nozzle, and that intake "flows equally" due to that ridiculous tube in there, I would say to put it as close to the tb as possible.
    The turbulance and distance should do a fine job of atomizing the mix...

    But lets not forget "reversion" from the cam here.

    When #1 opens, followed by #2, ect the mix will go to which cylinder needs it while the rest of the cylinders "rebound" the air due to reversion and force it towards the cylinders with an open port till its thier time to "suck"...lmao

    STICKERS = HORSE POWER !!!!!!!

    Leave a comment:


  • Z26-T
    replied
    Would look even better without all those stickers everywhere under your hood...looks like underneath the hood of a civic (no offence to you sticker happy people).

    Leave a comment:


  • 3400-95-Modified
    replied
    Yes as you can see a little more work is required like relocating the coil packs and such... but it would look hot all done up with shiny stainless tubing. HAWT!!!

    Leave a comment:


  • IsaacHayes
    replied
    Like this:
    This
    This
    and This

    Leave a comment:

Working...