Lots of TGP stuff for sale

[G-U-NOT]

PM sent!!

[Daguse5853Z]

you should have sold me the TGP kit when I offered...too bad I found another kit already.

[94GPGTP]

do u know where i can get a upper charge pipe?

[CobraCDR]

bump!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!!

[CobraCDR]

bumpy!!!!!!

[CobraCDR]

bump!

[3100 MPFI]

you know. If you use a flat tappet cam and flat tappet lifters in a 3100 block, I THINK you can use 3.1 MPFI pushrods. We were discussing this in a different thread.

[CobraCDR]

Kenny, all 3100's are ROLLER CAMS. I think you meant to say that 1995 is a roller with stamped steel rockers. All GEN 2's are FLAT TAPPET CAMS with STAMPED STEEL rockers. All GEN 3's are ROLLER CAMS with 1993-1995 being STAMPED STEEL rockers, and 1996+ being ROLLER FULCRUM rockers.

I HAVE seen a few 1996's with the STAMPED STEEL rockers, but all of those were in CHEVY's and I have no proof that the heads had not been swapped in.

Thanks I could not remember. So the answer is no, not without custom pushrods correct tat?

[3100 MPFI]

Kenny, all 3100's are ROLLER CAMS. I think you meant to say that 1995 is a roller with stamped steel rockers. All GEN 2's are FLAT TAPPET CAMS with STAMPED STEEL rockers. All GEN 3's are ROLLER CAMS with 1993-1995 being STAMPED STEEL rockers, and 1996+ being ROLLER FULCRUM rockers.

I HAVE seen a few 1996's with the STAMPED STEEL rockers, but all of those were in CHEVY's and I have no proof that the heads had not been swapped in.

[CobraCDR]

im interested in the wheels. but wouldnt be able to get them till the 1st week of feb. and you wouldnt have to ship as i could pick them up

PM Sent

[CobraCDR]

will the cam fit a 96 3100?? is it any differnt than the stock one in the 3100 if it does fit..??

Cam will fit but you would have to do a lot of uneccessary work for it to function. It is a flat tappet cam/lifter set. 95 3100's used flat tappet cams ( I think) with stamped steel rockets. You have a roller cam and roller rockers. You would have to back retrofit your 3100 for it to work. I'm not trying to discourage you, but for your application it would be better (and cheeper) to just buy a crane cam designed for a roller application. Or get a stock 3100 cam custom ground by them. Either way, you can make it work. I hope that answers your question.

[geldartb]

im interested in the wheels. but wouldnt be able to get them till the 1st week of feb. and you wouldnt have to ship as i could pick them up

[94GPGTP]

will the cam fit a 96 3100?? is it any differnt than the stock one in the 3100 if it does fit..??

[CobraCDR]

Prices Lowered

Prices lowered and added a new engle camshaft, new lifters and stock timing set. See original post for specs. This stuff has to go, taking offers!

Ken

[CobraCDR]

I want some parts, kenny, but I am a poor SOB. When I get some money, I might hit you up for some of the parts I am missing for my turbo project (if you still even have them).

I will still have them I'm sure, that TGP engine I bought is no good so now I have 2 sets of TGP stuff. I'm going to keep one set of parts and turbo the 2.8 and be done with it. The other set is the stuff I'm trying to sell here, and one TGPforums and even w-body. No serious bites yet other than the upper charge pipe. We will see I guess it can't hurt to have spares!